Impactors
A new cascade impactor has been designed for the OINDP Industry, specifically for pharmaceutical inhaler testing. It is the most efficient and accurate way to do standard in vitro APSD testing.
Sampling device substitute for the respiratory tract as a collector of airborne particles, and as such, it shall reproduce to a reasonable degree the lung penetration by these particles.
The 6 stage Viable Multistage Impactor is a multi-orifice, cascade impactor widely used as a standard to measure the concentration and particle size distribution of culturable bacteria and fungi in ambient air as well as other bioaerosols, like viruses.
ACI 2 Stage — Two-Stage Viable Cascade Impactor
The 2-Stage Viable Andersen Cascade Impactor collects airborne bacteria and fungi for culture-based counting. A configuration of the 6-stage viable ACI, it separates particles into respirable and non-respirable fractions for applications that require counts by fraction and a total viable count.
The impactor operates at 28.3 L/min and collects particles directly onto culture media in 90 mm Petri dishes. After incubation, colony counts are used to estimate the concentration of culturable bacteria or fungi per unit volume of air sampled. Its stainless steel construction withstands repeated cleaning.
ACI 1 Stage — Single-Stage Viable Impactor
The 1-Stage Viable Andersen Cascade Impactor collects airborne bacteria and fungi to estimate their concentration per unit volume of air. Its single sampling stage uses 400 jet orifices to direct airborne particles onto culture media in a 90 mm Petri dish.
At 28.3 L/min, the impactor has a particle cut-off of 0.65 µm. An optional pre-separator removes coarse particles before they reach the sampling stage. The stainless steel construction withstands repeated cleaning, and typical sampling times range from a few minutes to 30 minutes, depending on the environment and monitoring objective.
Impingers
GTI — Glass Twin Impinger
The Glass Twin Impinger (GTI) is a laboratory device used in the testing of inhalation products, particularly for determining the aerodynamic particle size distribution of aerosols emitted from inhalers. It operates at a specific flow rate (usually 60 L/min) and uses a two-chamber system to separate particles based on their size.
A device used to collect and analyse airborne particles by drawing air through a series of liquid-filled stages. Each stage captures particles of different sizes by impaction into the liquid, which allows for subsequent analysis of the particles.
Aerosol Generators & Nebulisers
DDS AERO is a pneumatic-type nebulizer that produces monodisperse and polydisperse aerosol for different applications.
The Laskin Aero X generates a consistent, repeatable test aerosol for HEPA and ULPA filter testing, particle filtration efficiency (PFE) testing, instrument calibration and aerosol research. It uses compressed air and Laskin nozzles to atomise test liquids such as DEHS and DOP. The working pressure can be adjusted to control aerosol output and particle size distribution.
X-Collison Nebulizer
The X-Collison generates a stable, polydisperse aerosol of submicrometre particles for laboratory testing and research. It can atomise solutions and suspensions, with supported materials including DOP, olive oil and polystyrene latex spheres.Its dual-chamber Collison jet design provides two aerosol output lines with different particle size ranges. Each line can deliver concentrations of up to 10⁷ particles/cm³.
Cyclone AGC
Generation of solid particles out of suspensions, solutions and biological agents with vertical or curved drying section.A special nozzle that enables the atomisation of salt solutions with highest dosing constancy.
X-SLPG and X-MLPG
SINGLE AND MULTIJET NEBILIZERS (BLAM type)
The X-LPG is a high-output liquid aerosol generator available in X-SLPG and X-MLPG variants. Based on the Collison jet nebulisation principle, it efficiently atomises a range of liquids in either single-pass or recirculating configurations.
Microbiological Samplers
The Delta Microbial Air Sampler (MAS) is ideal for use in sealed compartments, research, clean rooms, aseptic environments, pharmaceutical validation and inside hospitals.
Bravo Basic R
Coming Soon
Pumps & Software
PSP-G1 — Power Stream Pump
PSP-G1 is an oil-free rotary vane vacuum pump designed for laboratory inhaler testing. It maintains test airflow of up to 100 L/min against the pressure drop across an impactor, supporting repeatable aerosol particle size distribution (APSD) measurements.
The PSP-G1 can be used with a Next Generation Impactor (NGI) for dry powder inhaler testing and with an 8-stage Andersen Cascade Impactor (ACI) for metered-dose inhaler testing.

